溶解式吹干機

◆車輛的特點 Product features

※更具平衡同一的排氣壓為和露點

1.吸塔之的高度與網套直徑經實踐的結果精密模具統計，塔床阻礙小，以確保了縮減氣態晾干劑5秒的接觸周期，考慮生產設備氣的露點規范。

2.30％的空氣烘干劑留量，中用賠償金空氣烘干劑的當然光老化，有效確保空氣烘干。

3.特大型傳播器，抓好環流豎直依據干劑層，解除溝流表現。

※重復氣量損失不大于14％

1.有遠見的機筒開發，存放100％的吸附性熱量，存儲的熱量于延長恢復分階段的恢復氣濕度，不斷提高設備的解吸的能力，因此恢復更全面。

2.干燥處理和降解利用通過反向的方式給回對流傳熱工作方案，濕空氣的流淌干的過濾劑法定期限果比較好。降解利用氣進口含濕量控住在亞飽合壯態，使排氣閥消音器器及排氣閥檢修通道無起霜之慮。

3.可只能根據太干機的運動裝載需要轉換回收氣容量，保持回收氣旋多次不穩，回收阻力低至臨介。

※粗糙劑的使用人類使用期限長

1.恰當的機筒外形尺寸，使氣體順利通過變干劑層的流動速度和事件持續好的程序，積極充分調動變干劑的功能。

2.合適的程序調試，在熱空氣邁入機筒前，經除油整理有效解決熱空氣中內殘油物與重廢棄物物，防范烘干劑層受廢棄物。

※機械分為了創意高產品質量電動式及氣動彈簧閥和是真的嗎的全電子可程序編寫序管控器，人與機器工具欄信賴，自主間隔現示雙塔工程，循環往復時間實地可編，出產調整10min。管道閥門耐用度將近50萬次動作。

※鍋筒罐壁作冷熱鍍鋅防繡處置，10年不氧化。

※運動精準、性能方面比較穩定、操作方法簡便計算，布置不能自己依據。

※Bend it out on the same has the stable pressure and dew point

1. The height and diameter adsorption tower by the experimental results calculated precisely, tower, ensure the small resistance bed compressed gas desiccant 5 seconds contact time, meet the requirements of the finished product angry dew point.

2.30% of the surplus, desiccant used to compensate for the natural aging, ensure desiccant dry.

3. Large diffuser, ensure uniform through the desiccant air layer, eliminate channel flow phenomenon.

※Bend the gas loss less than 14% renewable

1. Excellent barrel design, save 100% of the adsorption quantity of heat, storage quantity of heat is used to increase the regeneration stage again angry temperature, improve equipment desorption ability, make renewable more thoroughly.

2. Dry and regeneration of the reverse convection scheme, wet air through the dry when the adsorbent best effect. Getting angry export moisture content control in the saturated state, the muffler and exhaust passage without concentrations of condensation.

3. According to the operation of the dryer load demand adjust dosage, ensure again angry for stability, regeneration renewable air pressure low to critical.

※Bend desiccant long service life

1. The right of barrel size, make the gas through the desiccant flow velocity and time of layer be the best, give full play to the desiccant performance.

2. The reasonable system configuration, in the air into the barrel, except by the efficient before oil processing timely removal in the air in content and heavy oil pollutant, avoid desiccant layer contamination.

※The equipment adopts bend novel high quality and pneumatic valve electric and advanced and reliable full electronic programmable controller, friendly interface, automatic continuous display of the twin towers, working cycle, the programmable factory set 10 min. The valve life for 500000 times action.

※Bend the cylinder body wall be cold galvanizing antirust processing, 10 years don't rust.

※Bend action, stable performance, accurate, easy operation and installation with no need of foundation.

◆注意技術應用運作 Main technical parameters